人人爽人人澡,欧美性灌满护士,天天玩天天配天天操天天摸,久久久久欧洲精品蜜臀

丁基膠涂布機自動涂膠基本過程

時間:2022-11-04 來源:http://www.leblanc.com.cn/ 發布人:昌盛機械

自動涂膠基本過程
Basic process of automatic gluing
1.測寬:第一次使用或鋁框?qū)挾雀淖兒?,需要對鋁條進行測寬,以便傳送時鋁框順利通過膠嘴。
1. Width measurement: after the first use or the width of the aluminum frame is changed, the aluminum strip needs to be measured so that the aluminum frame can pass through the rubber nozzle smoothly during transmission.
2.加熱:進入自動狀態后,膠嘴和膠盤要行加熱,同時傳送帶轉動,以免膠嘴溫度升高后將傳送帶燙壞,溫度高于80度以后打膠流程才會起效。
2. Heating: After entering the automatic state, the rubber nozzle and rubber plate shall be heated first, and the conveyor belt shall rotate at the same time, so as to prevent the conveyor belt from being damaged after the temperature of the rubber nozzle rises, and the gluing process will take effect only after the temperature is higher than 80 degrees.
3.傳送打膠:當達到設定溫度后,手持鋁框放在傳送帶上,當前端打膠光電檢測到鋁框時,自動涂膠過程開始。打膠光電有信號后,延時一段時間,前壓輪下壓,壓住鋁框;前壓輪下壓后延時一段時間,膠缸前進,膠嘴出膠。開始涂膠后,再延時一段時間,后壓輪下壓。打膠光電信號消失后,延時一段時間,前壓輪抬起,前壓輪抬起后,再延時一段時間,膠缸停止前進,同時膠嘴停止涂膠;停止涂膠后,再延時一段時間后,后壓輪抬起,鋁框一邊涂膠完成。
3. Transfer gluing: when the set temperature is reached, the hand-held aluminum frame is placed on the conveyor belt. When the aluminum frame is detected by the current end gluing photoelectric detector, the automatic gluing process starts. After there is a signal from the gluing photoelectric device, delay for a period of time, and press down the front pressing wheel to press the aluminum frame; After the front pressing wheel is pressed down, the rubber cylinder will move forward and the rubber nozzle will discharge. After the gluing is started, delay for a while, and press down the rear roller. After the photoelectric signal of glue application disappears, delay for a period of time, and the front roller lifts. After the front roller lifts, delay for a period of time, and the rubber cylinder stops moving forward, and the rubber nozzle stops applying glue; After stopping the gluing, after a further delay, the rear pressing wheel lifts and the gluing on one side of the aluminum frame is completed.


之后重復傳送打膠流程,將鋁框剩余三邊全部涂上丁基膠,鋁框涂膠就全部完成。
After that, repeat the transmission and gluing process. Apply butyl glue to the remaining three sides of the aluminum frame, and the gluing of the aluminum frame will be completed.
因為大多數鋁框為方形而少數為圓形,所以在自動中可以進行方形和圓形的切換。當為圓形框涂膠時,中間壓輪壓住圓框,同時皮帶轉動,膠嘴出膠,松開腳踏開關該過程停止。
Because most aluminum frames are square and few are round, you can switch between square and round automatically. When applying glue to the round frame, the middle pressing wheel presses the round frame, while the belt rotates, the glue nozzle releases glue, and the process stops when the foot switch is released.
以上就是為大家介紹的有關雙組份打膠機詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://linshi.jncsjx.com
The above is a detailed introduction to the two-component sealant dispenser, and we hope it will be helpful to you. If you have any questions, please contact us. We will provide you with our service in the same manner http://linshi.jncsjx.com

聯系我們Contact us

  • 咨詢熱線:0531-85717458 13705446998
  • 公司地址: 山東省德州市齊河安頭鄉企巢工業園
  • 掃碼聯系我們:

截屏,微信識別二維碼

微信號:13705446998

// 日韩 人妻 丝袜 制服 中文| 36久久精品色综合| 五月丁香在线视频成人一区| 久久999精品直播| 中文av有码在线| 日韩一区二区免费色情电影| 亚洲欧美一区中文字幕二区| 欧美变态国产一区porn| 欧美欧美淫秽网站| 色AV吧亚洲精品| 国产精品午夜福利1| 国产精品第157页| 激情动态五月天婷婷婷| 久久精品234| 色天堂av一区二区| 国产美女人人做人人干人人操| 一区二区精品久久久久免费视频 | 欧美亚州3AAA| 香蕉在线看一区二区| 日本中文字幕久久看| 国产一区二区三区有限公司| 亚洲欧美激情精品一区二区| 三上悠亚激情AV一区二区| 日韩在线在线一卡| 亚洲三级久久久久久久| 久久国产白浆| 大香蕉99在线| 精品午夜一区二区三区| 99成人三级| 日本久久久久勉费扦入| 大香蕉伊人视频在线播放| 665566视频| 中文字幕无码免费电影| 亚洲三级1234| 大香蕉@qq.91| 图片区视频区免费视频区| 欧美人精品| 曰韩一欧美一国产www| 天天躁日日躁狠狠躁av麻豆男| 在线不日韩一区不卡| 一本色综合日日|